| Part Number | Description | Sources Available | Tool Request Qty |
|---|---|---|---|
| DHC29298-001 | CRACK STANDARD | 1 | |
| DHC29298-003 | CRACK STANDARD | RQST*We do not currently have a manufacturing solution for this item but will do our best to source it. | |
| PWA28403B | CRACK STANDARD | RQST*We do not currently have a manufacturing solution for this item but will do our best to source it. | |
| PWA45938 | CRACK STANDARD | RQST*We do not currently have a manufacturing solution for this item but will do our best to source it. | |
| PWA45942 | CRACK STANDARD | 1 |
RQST*: We do not currently have a manufacturing solution for this item but will do our best to source it.
Partial Match
| Part Number | Description | Sources Available | Tool Request Qty |
|---|---|---|---|
| 118-540-400 | STANDARD BLOCK ;SPECIFICATION: V1 ;CRACK SIZE: 1 MM | 1 | |
| 126 | SURFACE CRACK REFERENCE STANDARD | 7 | |
| 1448170 | CRACK STANDARD-NFE | 1 | |
| 2.837.01 | CRACK STANDARD-NFE | 2 | |
| 99A51107300000 | AIRBUS A330 REFERENCE STANDARD FOR SUBSURFACE CRACKS IN AL-ALLOY 51-10-16-991-011-A. PART 6, PAGE 615 FIGURE 610PROCEDURE B. Includes Test Report and Certificate of Conformance... | 5 | |
| AFNDT-0512A | Eddy Current Hole and Surface Crack Standard: 7075-T651 Aluminum.. Includes Test Report and Certificate of Conformance. | RQST*We do not currently have a manufacturing solution for this item but will do our best to source it. | |
| AFNDT-0512A. | Eddy Current Surface Crack Standard. EDM Notch Size: Total of 3 Notches, 0.005, 0.010, 0.020 Deep x .005W +/- .002 per 33B-1-2 WP 402 00. Includes Test Report and Certificate of Conformance. | RQST*We do not currently have a manufacturing solution for this item but will do our best to source it. | |
| AFNDT-0512T | Eddy Current Hole and Surface Crack Standard: 6AL-4v Titanium.. Includes Test Report and Certificate of Conformance. | RQST*We do not currently have a manufacturing solution for this item but will do our best to source it. | |
| AFNDT-3157 | Liquid Penetrant Standard. Meets the ASME Boiler Pressure Code, Section V & III, and MIL-I-23135-C. The cracked aluminum block is made from 2024 aluminum and is 3” x 2” x 3/8” thick. A 1/8" wide groove separates the blocks two sides to facilitate side-... | RQST*We do not currently have a manufacturing solution for this item but will do our best to source it. | |
| AFNDT-ECRC82040 | Eddy Current Crack Standard Magnesium AZ-31 | RQST*We do not currently have a manufacturing solution for this item but will do our best to source it. | |
| BHS6061-T6/C2 | Bombardier Bolt hole and surface crack reference standard 6061-T6, 15 Holes, .030 Midwall notches top plate, (2) .030 corner notches each hole on the bottom plate. .008, .020, .030 surface notches | RQST*We do not currently have a manufacturing solution for this item but will do our best to source it. | |
| ET.28 | Bombardier Bolt hole and surface crack reference standard 6061-T6, 15 Holes, .030 Midwall notches top plate, (2) .030 corner notches each hole on the bottom plate. .008, .020, .030 surface notches | RQST*We do not currently have a manufacturing solution for this item but will do our best to source it. | |
| NDT4153 | BOEING 747 REFERENCE STANDARD PART 4 57-30-08 PAGE 6 FIGURE 2. PROCEDURE FOR INSPECTING CRACKED RIVET PART NUMBER BACR15FH10DD17 | RQST*We do not currently have a manufacturing solution for this item but will do our best to source it. | |
| PWA28403 | EDDY CRACK STANDARD | 4 | |
| PWA84314 | SPL-15004 - EDGE CRACK CALIBRATION STANDARD | RQST*We do not currently have a manufacturing solution for this item but will do our best to source it. | |
| RS-502-C | ASTRA G100 REFERENCE STANDARD, 2 EDM FATIGUE CRACKS 2.4mm X 1.2mm (PG.613: 04-00-00 FIG.605) | 1 | |
| SPO-3932 | SLIDING PROBE CRACK STANDARD 2ND LAYER ALUMINUM - 1916915 -OLYMPUS | RQST*We do not currently have a manufacturing solution for this item but will do our best to source it. | |
| SRS-0824A | ALUMINUM SURFACE CRACK STANDARD | 3 | |
| SRS-0824M | MAGNESIUM CRACK STANDARD | RQST*We do not currently have a manufacturing solution for this item but will do our best to source it. | |
| TEK-9117 | CRACK STANDARD-EDDY CURRENT 1ST STAGE FAN BLADE | 1 | |
| U8860545 | MAGNESIUM CRACK STANDARD | RQST*We do not currently have a manufacturing solution for this item but will do our best to source it. | |
| V15A2.CS | STANDARD BLOCK ;SPECIFICATION: V1 ;CRACK SIZE: 1 MM | 1 |
RQST*: We do not currently have a manufacturing solution for this item but will do our best to source it.
Aviapool (Aviation Tool Pooling LLC) is a global company providing around the clock assistance for the planning, supply, and sourcing of tooling equipment to the commercial aviation marketplace.
We are making available to our customers a comprehensive one-stop solution in ensuring the right tooling equipment reaches you on time for your planned input needs. With a fully researched tooling database of over 600,000 items, across multiple aircraft types available to you, we are in a perfectly placed position to get you what you need on time and on budget.
We take your tooling requests, and source the items on your behalf. Just submit your items, and we do the rest.
